收藏本站
Configuration
5.3
Jumpers Configuration
Two types of jumpers are used on the SAM9M10-G45-EK board:
2-pin jumpers with two possible settings:
– Fitted: the circuit is closed
– Not fitted: the circuit is open
3-pin jumpers with two possible positions, for which settings are presented in the following tables.
Table 5-2. Jumpers Configuration
Default
Designation
Setting
Feature
Closed
J1-1
1-2
VDDUTMII
3V3
J1
Closed
J1-2
3-4
VDDUTIMC
1V
(combined
jumper array)
Closed
Closed
J1-3
J1-4
5-6
7-8
VDDCORE
VDDPLLUTMI
1V
1V
1-2
VDDIOP0
3V3
JP1
1-2
JP1
2-3
1-2
External power to VDDIOP0
VDDIOP1
3V3 nominal
3V3
JP2
1-2
JP2
2-3
1-2
External power to VDDIOP1
VDDIOP2
3V3 nominal
3V3
JP3
1-2
JP3
Forces power on.
2-3
External power to VDDIOP2
3V3 nominal
JP4
Opened
To use the software shutdown control, JP4 must be opened.
3V battery backup must be present and JP7 jumper set in position 1-2
1-2
VDDIOM0
1V8
JP5
1-2
JP5
2-3
1-2
External power to VDDIOM0
VDDIOM1
1V8 nominal
1V8
JP6
1-2
JP6
2-3
1-2
External power to VDDIOM1
VDDBU
1V8 nominal
Lithium 3V Battery
JP7
1-2
JP7
2-3
VDDBU
3.3V from regulator
JP8
JP9
JP10
Opened
Closed
Closed
BMS Enables Boot on the internal ROM; closed selects the boot from the external device connected
to NCS0
Enables chip select access, Boot on the NCS0 (MN10 Flash)
Enables chip select access, Boot on the NCS3 (MN11 NAND Flash)
JP11
Test point
JP11.1: SO
JP11.2: SI
JP11.3: SCK
JP12
JP13
Closed
Opened
Enables chip select access, Boot on the SPIO_NPCS0 (Serial DataFlash MN13)
Set address A0 low (MN12 Serial EEPROM), enable Boot access.
JP14
JP15
JP14.1 = Line_Out
Used to connect a Loudspeaker
JP14.3 = AGND
JP16
JP17-JP18
5-2
Closed
Test points
DISMDIX (MN18)
Give access to the four GPIOs of WM9711L
AT91SAM9M10-G45-EK User Guide
6495B–ATARM–21-Apr-10
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
AT91SAM9RL-EK KIT EVAL FOR AT91SAM9RL
AT91SAM9X35-EK KIT EVAL FOR AT91SAM9X35
AT91SAM9XE-EK KIT EVAL FOR AT91SAM9XE
AT93C46D-TH-T IC EEPROM 1KBIT 2MHZ 8TSSOP
AT93C46E-TH-T IC EEPROM 1KBIT 2MHZ 8TSSOP
AT93C46Y6-10YH-1.8 IC EEPROM 1KBIT 2MHZ 8DFN
AT93C56A-10TU-2.7 IC EEPROM 2KBIT 2MHZ 8TSSOP
AT93C86AY6-10YH-1.8 IC EEPROM 16KBIT 2MHZ 8MAP
相关代理商/技术参数
AT91SAM9M11 制造商:ATMEL 制造商全称:ATMEL Corporation 功能描述:AT91 ARM Thumb-based Microcontrollers
AT91SAM9M11B-CU 制造商:Atmel Corporation 功能描述:BGA, GREEN, IND TEMP,CRYPTO MRL B - Bulk 制造商:Atmel Corporation 功能描述:IC MCU ARM9 64KB ROM 324TFBGA 制造商:Atmel Corporation 功能描述:MCU 32BIT ARM9 324TFBGA 制造商:Atmel Corporation 功能描述:MCU, 32BIT, ARM9, 324TFBGA 制造商:Atmel Corporation 功能描述:BGA, Green, IND TEMP,CRYPTO MRL B
AT91SAM9M11-CU 功能描述:ARM微控制器 - MCU IND TEMP MRL A RoHS:否 制造商:STMicroelectronics 核心:ARM Cortex M4F 处理器系列:STM32F373xx 数据总线宽度:32 bit 最大时钟频率:72 MHz 程序存储器大小:256 KB 数据 RAM 大小:32 KB 片上 ADC:Yes 工作电源电压:1.65 V to 3.6 V, 2 V to 3.6 V, 2.2 V to 3.6 V 工作温度范围:- 40 C to + 85 C 封装 / 箱体:LQFP-48 安装风格:SMD/SMT
AT91SAM9N12-CU 功能描述:ARM微控制器 - MCU BGA Grn IT MRL A RoHS:否 制造商:STMicroelectronics 核心:ARM Cortex M4F 处理器系列:STM32F373xx 数据总线宽度:32 bit 最大时钟频率:72 MHz 程序存储器大小:256 KB 数据 RAM 大小:32 KB 片上 ADC:Yes 工作电源电压:1.65 V to 3.6 V, 2 V to 3.6 V, 2.2 V to 3.6 V 工作温度范围:- 40 C to + 85 C 封装 / 箱体:LQFP-48 安装风格:SMD/SMT
AT91SAM9N12-CUR 制造商:Atmel Corporation 功能描述:BGA,GREEN,IND TEMP,MRL A,T&R 制造商:Atmel Corporation 功能描述:BGA,GREEN,IND TEMP,MRL A,T&R - Tape and Reel 制造商:Atmel Corporation 功能描述:IC MCU ARM9 ROM 217BGA 制造商:Atmel Corporation 功能描述:BGA GREEN,IND TEMP,MRL A
AT91SAM9N12-EK 功能描述:开发板和工具包 - ARM EVAL KIT SAM9N12 RoHS:否 制造商:Arduino 产品:Development Boards 工具用于评估:ATSAM3X8EA-AU 核心:ARM Cortex M3 接口类型:DAC, ICSP, JTAG, UART, USB 工作电源电压:3.3 V
AT91SAM9R64 制造商:ATMEL 制造商全称:ATMEL Corporation 功能描述:Thumb Microcontrollers
AT91SAM9R64_09 制造商:ATMEL 制造商全称:ATMEL Corporation 功能描述:AT91 ARM Thumb Microcontrollers